Weaponsmithing discipline

Incomplete Article

• This article is incomplete, which means that while it is not a stub, it still lacks certain data or information.
• Needs construction stats added
• Please see Category:Incomplete articles for more articles that are incomplete.

Weaponsmithing is a crafting discipline of the Forging craft. There are places to practice it at the Riverhaven Forging Society, Crossing Forging Society, Shard Forging Society, Rathan Forging Society, Mer'Kresh Forging Society, the Hibarnhvidar Forging Society, Lava Forge and Iltesh Neg Degti Forge.

Basics

Using metal ingots produced by smelting, a weaponsmith shapes metal on an anvil with hammer and tongs, then polishes on a grinding wheel.

Shaping

The process for shaping weapons is the same as Blacksmithing.

Polishing

When it comes time to polish, first TURN GRINDSTONE until it is up to speed, then PUSH GRINDSTONE WITH <weapon>.

Techniques

See Weaponsmithing Techniques.

Products

See Weaponsmithing Products.

Weapon Enhancements

Enhancements are applied to the weapon after the final oiling.

The difficulty of performing these enhancements is one to three categories harder than the difficulty of crafting the base weapon. Failure in the process will damage the weapon sufficiently to require repair in a repair shop, though it will not cause any lasting damage.

Enhancing a weapon *requires* the appropriate weaponsmithing technique, though it can be done by a crafter other than one that created the weapon.

Honing

Honing requires a grindstone, a wire brush, and some oil.
Honing a finished weapon will reduce its weight by 8% (round up), but will not drop the weapon down below its 3 density equivalent, or by more than 5 stones. For each stone of weight removed, one point of impact is lost (point, not category).

• Note: a weapon can be honed or balanced, but not both!

Begin by STUDYing the appropriate page in your weaponsmithing book. Next TURN GRINDSTONE until it is up to speed, then PUSH GRINDSTONE WITH <weapon>. Periodically, you may be required to remove the metal shavings by RUBbing the weapon with a wire brush.

Tempering

Tempering requires a forge and tongs. Tempering will improve the durability of a weapon and increase its resistance to damage, if successful.

Begin by placing the weapon on the forge itself. The base activity requires TURNing the weapon with a set of tongs. Periodically, the crafter may be required to perform bellows and shovel actions as indicated in basic smelting or pounding.

Balancing

Balancing is an identical process to honing, but it will increase a weapon's balance, at the expense of suitability.

• Note: a weapon can be honed or balanced, but not both!

Follow the same procedure as honing, just begin with the appropriate weaponsmithing book page.

Weapon Repair

Weapon repair uses the same process as the Blacksmithing discipline.

Cleaning

RUBing a weapon with a cleaning cloth will allow you to bring out different aspects.

1. a <metal> <weapon>
2. a <metal> <weapon> with a tempered blade/head
3. a <metal> <weapon> with a <mod> blade/head/design/finish
4. a tempered <weapon>
5. a tempered <weapon> with a <mod> blade/head/design/finish
6. a <mod> <weapon>
7. a <mod> <weapon> with a tempered blade/head
8. a <weapon> with a tempered blade/head
9. a <weapon> with a <mod> blade/head/design/finish
10. a <weapon>

In this case <mod> means either "honed" or "balanced."
The blade/head/design/finish depends on weapon type and mod.

Construction

Nearly all weapons have the same construction, so far with the exception of sterak axe (crafted), serrated recade (crafted), and serrated kudalata (crafted).

Durability	Standard	Tempered Standard
90	14 - v.strong	18 - p. invulnerable
80	12 - q.guarded	17 - n.impervious
70	11 - r.reinforced	16 - u.resilient
65	10 - a bit	15 - e.resistant
60	09 - average	14 - v.strong
50	08 - marginally	12 - q. guarded
40	07 - appreciably	11 - r. reinforced
??	05 - p. weak	08 - marginally
25	04 - r.flimsy	06 - s.unsound
20	03 - q.fragile	05 - p.weak
??	02 - v.delicate	04 - r.flimsy

Behind the Scenes

Damage is affected by two stats, the hardness of the metal used, and the weight of the weapon.

• Base damage is set by the template, modified by metal hardness.
• For each stone of weight, one additional point of damage is added to a category, in a pattern determined by template.

Balance and suitability are also affected by hardness but also by the density (stones per volume).

• Balance and suitability share a pool of points, set by template and metal hardness.
• The inital ratio is set by the template.
• As the density of the metal increases past 5, the proportion of points is skewed towards suitability. As it decreases, it skews towards balance.

The construction of a weapon is solely dependent on the material's durability. So far, the only templates that have different durabilities are the rare, limited-use instructions.

Related Forum Posts

Click here to search for related posts.