Shapeshaft (script)
| Shapeshaft (script) | |
|---|---|
| Category | crafting |
| Front-end | StormFront,Wizard,Genie |
| Author | Pfanston |
Description
This script assumes you have some lumber to turn into shafts in the container that you keep your tools in. Only have as much in one stack of lumber as you want to turn into shafts. Right now it does not appear you need the shaping book to make shafts. I will not set up anything to stamp shafts if they can be stamped.
Note this script is set up for stormfront, wizard and genie. I have run it in all 3 front ends.
In the script I tend to put items in containers. But you can easily use stow left and stow right if your store help variables are set up I have the stow lefts and rights in here but they are commented out for the lines I tend to use. This script will also use all the lumber you have in your container1 so if you don't want it all turned into shafts don't put it all in the container1.
Instructions
parameters are .shapeshaft <container1>
example .shapeshaft bag
Step 1 - Get shaper fron container, get lumber from container, shape lumber into shaft.
Step 2 - put shaper away, All shafts are done.
To run type .shapeshaft bag
The only tool required to make shafts for arrows is a shaper. Your <container1> must be where you keep the tool and the lumber. Remember one thing in making shafts. Your shafts will be perfect if the lumber you use has a workability number that when you make the shafts they end up masterfully created. Second each shaft will handle 5 arrows. So if you use 20 count of lumber you will make enough shafts to handle the making of 100 arrows. I dont recommend having your lumber larger than 20 count for this. Even that may too heavy for younger folks. Do what you can put in the container and hold it. If you cant hold it. Mark my lumber at x pieces, get your scissors out, and cut lumber with my scissors. That will reduce the amount of Lumber used.
Script
<prep># example .shapeshaft bag
- This script assumes you have some lumber to turn into shafts in the container
- that you keep your tools in. Only have as much in one stack of lumber as you want
- to turn into shafts. Right now it does not appear you need the shaping book to make
- shafts. I will not set up anything to stamp shafts if they can be stamped.
- Step 1 - Get shaper fron container, get lumber from container,
- shape lumber into shaft.
- Step 2 - put shaper away, All shafts are done.
- To run type .shapeshaft bag
- The only tool required to make shafts for arrows is a shaper. Your <container1>
- must be where you keep the tool and the lumber. Remember one thing in making
- shafts. Your shafts will be perfect if the lumber you use has a workability number
- that when you make the shafts they end up masterfully created. Second each shaft
- will handle 5 arrows. So if you use 20 count of lumber you will make enough shafts
- to handle the making of 100 arrows. I dont recommend having your lumber larger than
- 20 count for this. Even that may too heavy for younger folks. Do what you can put
- in the container and hold. If you cant hold it. Mark my lumber at x pieces, get
- your scissors out, and cut lumber with my scissors. That will reduce the amount of
- lumber used.
- This script has nothing special in it, so it should work in the wizard front end,
- stormfront, and genie. In the script I tend to put items in containers. But you
- can easily use stow left and stow right if your store help variables are set up
- I have the stow lefts and rights in here but they are commented out for the lines
- I tend to use. This script will also use all the lumber you have in your container1
- so if you dont want it all turned into shafts dont put it all in the container1.
Start:
put glance match tool You glance down at your empty hands match stowboth You glance down to see
matchwait
tool:
pause 1 put get my shaper from my %1 match shaftend1 What were you referring to? match shapeshaft You get match tool ...wait
matchwait
shapeshaft:
pause 1 put get my lumb from my %1 match shaftend2 What were you referring to? match shapeshaft2 You get match shapeshaft ...wait
matchwait
shapeshaft2:
pause 1 put shape my lumber into shaft match stowleft Roundtime match shapeshaft2 ...wait
matchwait
stowleft:
pause 1
- put stow left
put put my shafts in my %1 match shaftend2 What were you referring to? match shapeshaft You put match stowleft ...wait
matchwait
stowboth:
pause .5 put stow left pause .5 put stow right pause .5
goto start
shaftend1:
pause 1 echo *** NO SHAPER TOOL IN %1 ***
exit
shaftend2:
pause 1
- put stow right
put put my shaper in my %1
waitfor You put
pause .5 echo *** OUT OF LUMBER ***
exit